View RE023_1301034.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* * * * * * * * * *
Low-noise Low Drop Out Voltage Regulator 2.6V Fixed Output Voltage 3V to 5.5V Supply Operation 160 mA Maximum Load Current Less Than 46 A (max) Quiescent Current Power-down Mode Consumption Less Than 1 A More Than 60 dB (Typical) PSRR at 1 kHz 68 VRMS Output Noise 0.35 m CMOS Technology Typical Application: Baseband Section Supply in Mobile Terminals
Description
RE023 is a Low Drop Out (LDO) voltage regulator macrocell with a fixed 2.6V output voltage, rated for loads up to 160 mA. It is designed to be integrated with other analog cells, digital logic, microcontrollers, DSP cores and memory blocks into system-onchip products. The circuit consists of a PMOS pass device, an error amplifier and a feedback resistive network, sized to achieve the required closed loop gain. These blocks make up the regulating loop. An over-current and short circuit protection circuit has been included to limit the output current delivered by the regulator, thus avoiding destruction in case of a short circuit. An external reference voltage (bandgap voltage) is necessary for correct functionality. The target reference voltage is 1.231V, delivered, for example, by BG019. Double pads on the supply voltage V BAT2B/VBAT2BB and output voltage VANINTA/VANINTAA are used to reduce the total output resistance. Current reference is generated inside the cell through a circuit supplied by a 2.5V 0.1V regulated input voltage on V SAUVC. Remote sense terminal VANINTS provides regulation at the load by connecting it to the output terminal near a critical point to improve performance of the regulator (e.g., connecting them at the package pin by double-bonding, thus avoiding the bonding resistance influence). A ceramic capacitor of 2.2 F connected from VANINTA/VANINTAA to ground is needed as external compensation. Figure 1. Symbol(1)
vbat2b vbat2bb
Embedded ASIC Macrocell: Power Management for Mobile Terminals (PM) RE023 Fixed 2.6V 160 mA LDO Voltage Regulator
vsauvc vbg
vaninta vanintaa on1 vanints
vanintc
gnd2
Note:
1. Pin names are written as they appear on the user screen when the symbol is opened in the design tool environment.
Rev. 2702B-PMGMT-02/03
1
Functional Diagram
Figure 2. Functional Diagram
VBAT2B VSAUVC VBAT2BB
ON1 ON1 IBIAS VBG ON1 Pass Device VANINTC VANINTA GND2 GND2 Current Sensing and Limiter R1 GND2 VANINTAA VANINTS
ON1
R2
ON1
GND2
Pin Description
Pin Name VBAT2B VBAT2BB VANINTA VANINTAA VANINTS VANINTC GND2 VSAUVC VBG ON1 I/O Power supply Power supply Analog output Analog output Analog output Analog output Ground Power supply Analog input Digital input Type External pad External pad External pad External pad External pad Internal pin Internal pin Internal pin Internal pin Internal pin Function Power supply Power supply Output voltage Output voltage Sense voltage Output voltage Ground Power supply Voltage reference Enable command Value 3V to 5.5V 3V to 5.5V 2.5V to 2.7V 2.5V to 2.7V 2.5V to 2.7V 2.5V to 2.7V 0 2.5V 0.1V 1.231V 0 or VBAT2B/VBAT2BB
2
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
2702B-PMGMT-02/03
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
Absolute Maximum Ratings*
VIN .......................................................... -0.3V to 6.5V Digital Signals......................................... -0.3V to 5.5V Output Current..................................Internally Limited Junction Temperature ..........................-40C to 150C
*NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Electrical Specifications(1)
TJ = -20C to 125C, VBAT2B/VBAT2BB = 3V to 5.5V unless otherwise specified, output capacitance = 2.2 F. Table 1. Electrical Specifications
Symbol VBAT2B/VBAT2BB VSAUVC Parameter Operating Supply Voltage Auxiliary Operating Supply Voltage Junction Temperature Range Output Voltage Output Current Quiescent Current Line Regulation Transient Line Regulation Load Regulation Transient Load Regulation IANINTA/IANINTAA = 160 mA IANINTA/IANINTAA = 160 mA rise time = fall time = 5 s 10% - 90% of max IANINTA/IANINTAA 10% - 90% of max IANINTA/IANINTAA rise time = fall time = 5 s @100 Hz @1 kHz VBAT = 3V @20 kHz @100 kHz @100 Hz PSRR Power Supply Rejection Ratio at Full Load @1 kHz VBAT = 4.25V @20 kHz @100 kHz @100 Hz @1 kHz VBAT = 5.5V @20 kHz @100 kHz 2 4 2 5 -65 -60 -40 -30 -60 -60 -50 -40 -55 -55 -48 -40 Condition Min 3 2.4 -20 2.5 2.6 2.5 Typ Max 5.5 2.6 125 2.7 160 46 3 7 3 10 Unit V V C V mA A mV mV mV mV dB dB dB dB dB dB dB dB dB dB dB dB
TJ
VANINTA/ VANINTAA IANINTA/ IANINTAA IQQ VDC VTRAN VDC VTRAN
3
2702B-PMGMT-02/03
Table 1. Electrical Specifications (Continued)
Symbol VN TR ISD ICC Notes: Parameter Output Noise Rise Time Shut Down Current Short-circuit current 1. Obtained by considering the parasitics of a TFBGA100 Package. 2. Obtained by using BG019 as reference voltage generator.
(2)
Condition Bandwidth: 10 Hz to 100 kHz output current = 160 mA 100% of IANINTA/IANINTAA 10% - 90% VANINTA/VANINTAA
Min
Typ 68
Max 81 70 1 400
Unit VRMS s A mA
4
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
2702B-PMGMT-02/03
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
Control Modes
All digital signals are referred to the supply voltage VBAT2B/BAT2BB. Table 2. Truth Table
ON1 0 1 VANINTA/VANINTAA Power down (High-Z) Power on, VANINTA/VANINTAA = 2.6V
Application Example
A ceramic capacitor of 2.2 F with ESR between 20 m and 250 m connected from VANINTA/VANINTAA to ground is needed as external compensation.
Description Capacitor, CL Min 1.8 Typ 2.2 Max 2.6 Units F
Figure 3. Application Example
2.5V Regulator (e.g., RE031)
2.5V
VSAUVC
VBAT2B VBAT2BB
1.231V Bandgap (e.g., BG019)
VBG VANINTA VANINTAA ON1 VANINTS
Battery Pack
CL
Digital Core VANINTC
GND2
5
2702B-PMGMT-02/03
Typical Performance Characteristics (Conditions specified on page 8)
Static Line Regulation at Full Load 1
O u tp u t V o lta g e C h a n g e [m V ] S ta tic L o a d R e g u la tio n
15
Output Voltage Change [mV]
10
0
5 V B AT = 3V 0 V B AT = 4.25V V B AT = 5.5V
-1
-2
-5
-3 3 3.5 4 4.5 5 5.5 Battery Voltage [V]
-10 0 20 40 60 80 100 120 140 160
O u tp u t C u rre n t [m A ]
Transient Line Regulation at Full Load 2.598 2.597 2.596 Output Voltage [V] 2.595 2.594 2.593 2.592 2.591 2.590 2.589 2.588 0.35 0.4 0.45 Time [ms] 0.5 0.55
2.588 2.586 0.35
O u tp u t V o lta g e [V ]
T ra n sie n t L o a d R e g u la tio n
2.600 2.598 V B A T = 3V 2.596 2.594 2.592 2.590 V B A T = 4.25V
V B A T = 5.5V
0.4
0.45
T im e [m s]
0.5
0.55
6
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
2702B-PMGMT-02/03
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
Typical Performance Characteristics (Conditions specified on page 8)
P o w e r S u p p l y R e j e cti o n Ra ti o a t F u l l L o a d
P o w e r S u p p ly R e je ctio n R a tio a t F u ll L o a d ve rsu s B a tte ry V o lta g e 100000
10 -30 -35
100
1000
10000
3.0 -30 -40
3.5
4.0
4.5
5.0
5.5
-40
P S RR [d B]
-45 -50 -55 -60 -65 V B A T = 3V
V B A T = 4.25V
P S R R [d B ]
V B A T = 5.5V
-50 Freq = 1 k Hz -60 -70 -80 Freq = 100 Hz -90 Freq = 100 k Hz Freq = 20 k Hz
F re q u e n c y [Hz ]
B a tte ry V o l ta g e [V ]
L D O S ta rtu p a t F u ll L o a d fo r V B AT = 4.25V
O u tp u t N o ise S p e ctru m a t F u ll L o a d a n d V B AT = 4.25V
5 4.5 4 3.5
V o lta g e [V ]
1.0E -10
O N1 O u tp u t N o ise [V /sq rt(Hz )]
1.0E -11
Total output nois e 68 V R MS
3 2.5 2 1.5 1 0.5 0 0 20 40
T im e [ s]
V AN IN T
1.0E -12
1.0E -13
1.0E -14
60 80 100
10
100
1000
F re q u e n cy [Hz ]
10000
100000
7
2702B-PMGMT-02/03
Terminology
Line Regulation Measures the maximum transient and DC variations of the output voltage of the LDO when the supply changes between two specified values with fixed load current; minimum rise time and fall time is 5 s. Figure 4. Line Regulation
3.4V(5.4V)
VBAT2B/VBAT2BB 3V(5V) 5 s VANINTA/VANINTAA VTRAN 5 s
VDC
Load Regulation
Measures the maximum transient and DC variations of the output voltage of the LDO when the load current changes between two specified values with fixed power supply; minimum rise time and fall time is 5 s. Figure 5. Load Regulation
90% of max IANINTA/IANINTAA IANINTA/IANINTAA 10% of max IANINTA/IANINTAA
5 s
5 s
VTRAN VANINTA/VANINTAA VDC
8
RE023 Fixed 2.6V 160mA LDO Voltage Regulator
2702B-PMGMT-02/03
Atmel Headquarters
Corporate Headquarters
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
(c) Atmel Corporation 2003. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. ATMEL (R) is the registered trademarks of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper.
2702B-PMGMT-02/03 0M

▲Up To Search▲

Price & Availability of RE023

	To Download RE023 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .